# Moisture content for briquetting

> Wood waste needs to be below about 15% moisture to press into solid briquettes. Falach presses list a maximum of 15%, and the BrikStar EK 20 works best below 12%. Waste from kiln-dried timber is usually dry enough. Green sawmill waste usually is not.

- URL: https://briquette-machines.co.uk/waste/moisture-content/
- Updated: 18 November 2026

## Why does moisture matter so much?

A hydraulic briquette press relies on pressure, and the heat that pressure creates, to soften the lignin in wood so it binds. Too much water gets in the way. The briquette comes out soft, splits or crumbles, and the press works harder for a poorer result. IWM’s guidance for the BrikStar EK gives a range of 8% to 15%, so very dry material is worth testing too.

## What the machines say

Machine |
Moisture limit (as published) |

[Falach 20](/machines/falach-20-briquette-machine/) and [Falach 20XL](/machines/falach-20xl-briquette-machine/) |
15% maximum |

[Falach 50](/machines/falach-50-briquette-machine/) |
15% maximum |

[Falach 100](/machines/falach-100-briquette-machine/) |
15% maximum |

[BrikStar EK 20](/machines/brikstar-ek-20/) |
Up to ~15% by weight, optimal below 12% |

Treat 15% as the ceiling across the Falach range, and aim lower if you can.

## Is my waste dry enough?

Source |
Usually dry enough? |

Joinery, furniture and shopfitting using kiln-dried timber and board |
Usually yes |

MDF and board dust |
Usually yes |

Timber merchant cutting service (kiln-dried stock) |
Usually yes |

Sawmill cutting green logs |
Usually no, needs drying |

Air-dried or outdoor-stored timber |
Check it |

Pallet wood |
Check it, often variable |

Any waste stored outside or in an open skip |
Check it |

Kiln-dried joinery timber is typically dried to somewhere around 8–12% moisture, so its waste usually suits a press. Freshly felled timber is often well above 30%.

## How do I measure moisture content?

- **A moisture meter.** Pin-type meters work on solid wood. For dust and shavings, use a meter made for loose material, or the oven-dry method below.

- **The oven-dry method.** Weigh a sample, dry it in a low oven until its weight stops falling, and weigh it again. Moisture content (wet basis) = (wet weight − dry weight) ÷ wet weight × 100.

- **Send us a sample.** A [briquetting trial](/book-a-trial/) shows how your waste actually presses.

**Example:** a 500 g sample of sawdust weighs 420 g once dried. (500 − 420) ÷ 500 × 100 = 16%. Just over the limit, so it would need some drying.

## What if my waste is too wet?

- **Store it dry.** Keep extraction bags and silos under cover. Damp storage is the most common cause of wet waste in workshops.

- **Separate wet and dry streams.** If only one machine cuts wet timber, keep its waste apart.

- **Dry it.** Sawmills usually need a drying stage before a press. Talk to us about volumes.

## Do briquettes pick up moisture after pressing?

Yes. Dry briquettes are absorbent. If they get wet they swell and break up. Store them indoors, off the floor and away from damp walls. Bagged briquettes are easier to keep dry.

## Thinking of selling briquettes? Check first

Wood fuel sold to households in the UK may fall under Ready to Burn or Woodsure rules, which include moisture limits. Check the current requirements before offering any.

**Check the rules before you burn them.** Briquettes made from treated, painted or board materials (MDF, chipboard, laminate) are still waste wood, and burning them may need an environmental permit or a registered exemption. Check with the Environment Agency (or SEPA in Scotland, Natural Resources Wales or NIEA in Northern Ireland) and your local authority. Selling wood fuel to households has its own certification rules (Ready to Burn or Woodsure), so check before offering any. We are happy to talk it through with you, but we can’t give you a ruling for your site.

Not sure which machine fits? [Send us a sample of your waste or come and see a machine running](/book-a-trial/), or [ask IWM](/contact/) on 01636 918280.

## Models that fit

- [Falach 20 Briquette Machine](https://briquette-machines.co.uk/machines/falach-20-briquette-machine.md): 10–25 kg/h
- [Falach 50 Briquette Machine](https://briquette-machines.co.uk/machines/falach-50-briquette-machine.md): 40–60 kg/h
- [Falach 100 Briquette Machine](https://briquette-machines.co.uk/machines/falach-100-briquette-machine.md): 90–120 kg/h
- [BrikStar EK 20](https://briquette-machines.co.uk/machines/brikstar-ek-20.md): 10–30 kg/h

## Questions and answers

**What moisture content is needed for briquettes?**
Below about 15%. Falach presses list 15% as the maximum. The BrikStar EK 20 accepts up to about 15% and works best below 12%.

**Why are my briquettes falling apart?**
Moisture is the most common reason. Above about 15% the briquettes don't bind. Very coarse or uneven material can also be a factor.

**Can I briquette green sawdust?**
Not as it comes. Green sawdust is usually well over 15% moisture and needs drying first.

**How do I measure moisture in sawdust?**
Weigh a sample, dry it in a low oven until the weight stops falling, then reweigh. (Wet − dry) ÷ wet × 100 gives moisture content.

**How should I store briquettes?**
Indoors, dry and off the floor. Wet briquettes swell and break up.

## Who runs this site

- Briquette Machines (https://briquette-machines.co.uk/) is run by International Woodworking Machinery Ltd, trading as IW Machines (IWM). Main website: https://www.iwmachines.co.uk/
- What they do: supply, install and service briquette presses that turn wood waste (sawdust, shavings, chippings) into solid briquettes, for joinery workshops, sawmills, pallet makers, timber merchants, furniture makers, shopfitters and wood fuel producers across the UK. Brands: Falach (main range) and BrikStar. Also used and ex-demo briquetters.
- Address: Unit 20, Newark Business Park, 3 Brunel Drive, Newark, Nottinghamshire NG24 2EG, United Kingdom
- Phone: 01636 918280
- Email: info@iwmachines.co.uk
- Opening hours: Mon–Fri 8am–5pm; weekends by appointment
- Also in Newark: Unit 29, service and refurbishment workshop (the showroom and demonstration area is Unit 20)
- IWM founded: April 2009 by Ian Brown, who has worked in the woodworking machinery trade since 1973, when he started as an apprentice at Wadkin
- Companies House number: 06872243
- VAT number: 971462605
- Try before you buy: briquetting trials with the buyer's own waste: https://briquette-machines.co.uk/book-a-trial/
- Enquiries: https://briquette-machines.co.uk/contact/
