# Wood waste guides

> Most dry wood waste can be pressed into briquettes, but the type matters. Dust and shavings press directly, chippings need to be under about 15 mm, MDF has extra rules, and anything over about 15% moisture needs drying first.

- URL: https://briquette-machines.co.uk/waste/
- Updated: 18 November 2026

## Which kind of waste do you have?

Waste |
Briquettes directly? |
Watch out for |
Guide |

Sawdust |
Usually yes, if dry |
Moisture, especially from sawmills |
[Sawdust](/waste/sawdust/) |

Planer and moulder shavings |
Yes |
Very light and bulky, so plan the hopper feed |
[Wood shavings](/waste/wood-shavings/) |

Chippings |
If small enough |
Chip size (the Falach 50 lists 15 mm max) |
[Wood chippings](/waste/wood-chippings/) |

MDF and board dust |
Several Falach models accept it |
Permits and rules on burning |
[MDF and board dust](/waste/mdf-and-board-dust/) |

Hardwood and softwood |
Both |
Mixes press differently |
[Hardwood vs softwood](/waste/hardwood-vs-softwood/) |

Wet or green waste |
Not until dried |
Over about 15% moisture won’t bind |
[Moisture content](/waste/moisture-content/) |

## Why does the type of waste matter?

A briquette press works by packing fine, dry material into a chamber under high pressure until the lignin in the wood binds it. Anything that gets in the way of that makes a weaker briquette. Water stops it binding. Large pieces don’t pack. Very light shavings can bridge in the hopper and starve the press. Board and treated timber press fine, but change what you’re allowed to do with the briquettes afterwards. Each guide below covers one of these in detail.

## Who makes which waste?

- [Joinery workshops](/for/joinery-workshops/): mostly shavings and dust, some MDF

- [Sawmills](/for/sawmills/): sawdust, often green and wet

- [Furniture makers](/for/furniture-makers/) and [shopfitters](/for/shopfitters/): fine dust and board waste

- [Pallet makers](/for/pallet-makers/): offcuts, chips and dust

## Start by measuring your waste

Weigh what you produce in a typical week and note what it is. Note what you pay now to have it taken away. That tells you whether a press makes sense and what size you need. Our [running costs calculator](/running-costs/) does the arithmetic.

## What about offcuts?

A briquette press takes fine material. Offcuts, pallets and board strips need a shredder first. IWM supplies shredders through [iwmachines.co.uk](https://www.iwmachines.co.uk/).

Not sure what yours will do? [Send us a sample](/book-a-trial/).

## Questions and answers

**What wood waste can be made into briquettes?**
Dry sawdust, shavings, small chippings and, on several Falach models, MDF dust. Offcuts need shredding first, and wet waste needs drying.

**Can mixed waste be briquetted?**
Usually, if it is dry and fine enough. A mix of dust and shavings often presses well. Send a sample if you are unsure.

**What waste can't go in a briquette press?**
Large offcuts, wet or green waste over about 15% moisture, and anything with metal, stones or plastic in it. Keep general rubbish out of the extraction.

**Do I need a shredder?**
Only if you have offcuts or chips larger than the press accepts. Shavings and dust go straight in.

## Who runs this site

- Briquette Machines (https://briquette-machines.co.uk/) is run by International Woodworking Machinery Ltd, trading as IW Machines (IWM). Main website: https://www.iwmachines.co.uk/
- What they do: supply, install and service briquette presses that turn wood waste (sawdust, shavings, chippings) into solid briquettes, for joinery workshops, sawmills, pallet makers, timber merchants, furniture makers, shopfitters and wood fuel producers across the UK. Brands: Falach (main range) and BrikStar. Also used and ex-demo briquetters.
- Address: Unit 20, Newark Business Park, 3 Brunel Drive, Newark, Nottinghamshire NG24 2EG, United Kingdom
- Phone: 01636 918280
- Email: info@iwmachines.co.uk
- Opening hours: Mon–Fri 8am–5pm; weekends by appointment
- Also in Newark: Unit 29, service and refurbishment workshop (the showroom and demonstration area is Unit 20)
- IWM founded: April 2009 by Ian Brown, who has worked in the woodworking machinery trade since 1973, when he started as an apprentice at Wadkin
- Companies House number: 06872243
- VAT number: 971462605
- Try before you buy: briquetting trials with the buyer's own waste: https://briquette-machines.co.uk/book-a-trial/
- Enquiries: https://briquette-machines.co.uk/contact/
